4
2.0 INSTALLING THE DISPLAY
EPAX DISPLAY INSTALLATION
The EPAX display is intended to be mounted
into a panel or enclosure. The display is provided
with a gasket to provide a water-tight seal. The
recommended minimum panel thickness for
NEMA 4/IP65 sealing is 0.060" (1.57 mm).
For panel mounting, prepare the panel
cut-out to the dimensions shown in
Figure 3. The supplied template may be
used to mark the cut-out and hole
locations on the panel. After the panel
cut-out has been deburred, slide the
panel gasket over the rear of the display
and onto the mounting studs. Insert the
display into the panel cut-out as
illustrated in Figure 4. Install 14 #
10-32 keps nuts (supplied) and tighten
evenly for uniform gasket compression.
Do not over-tighten the nuts.
By using additional mounting accessories,
the EPAX can be surface-wall mounted, suspended,
or bottom mounted. Separate installation instructions are
provided with the mounting accessories.
Environment And Cleaning
The display should be installed in a location that does
not exceed the maximum operating temperature and
provides good air circulation. Placing the system near
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and
neutral soap product. Do NOT use solvents. Continuous
exposure to direct sunlight may accelerate the aging
process of the bezel.
CAUTION:
12
3
456
7
89
1011
DISCONNECT ALL
POWER BEFORE INSTALLING OR
REMOVING MODULE
SLOT
TWIST
!
WHILE FIRMLY DEPRESSING REAR FINGER TABS (TOP & BOTTOM),
INSERT SCREWDRIVER BLADE (3/16" OR 1/4") INTO NARROW SLOT
(AT THE ARROW) AND TWIST IN THE DIRECTION SHOWN.
TO REMOVE MODULE:
MODEL LPAX
RED LION CONTROLS
YORK, PA. MADE IN U.S.A.
PAXCDC10
RS485 COMMUNICATION
12
13
14
15
- B(-)
- A(+)
- COMM
- N/C
1
2 3 4 5 6 7
8 9
10 11
~~
AC AC
85-250VAC
50/60Hz
14VA
COMMUNICATION OPTION ANALOG OUT OPTION SETPOINT (SP) OPTION
MODEL PAXD
RED LION CONTROLS
YORK, PA. MADE IN U.S.A.
SEE LITERATURE FOR
JUMPER SELECTION
SIGNAL INPUTS
USER INPUTS
VOLT/OHM
CURRENT
+EXCITATION
COMM
1
2
3
N/C
COMM
!
R
-19
17
+18
-
+16
ANALOG OUTPUT
PAXCDL10
RLY3
25
21
RLY2
22
COMM
RLY1
20
QUAD RELAY S.P.
PAXCDS20
0-10V
ANALOG
OUTPUT
OUTPUT
ANALOG
0-20mA
24
23
COMM
RLY4
RELAYS RATED
3A @ 250VAC
(RESISTIVE LOAD)
CAUTION
DISCONNECT
ALL POWER
BEFORE
OPENING
MODULE
RETENTION
LATCH (TOP
AND BOTTOM)
MOUNTING
PANEL
PANEL
GASKET
FRONT
PANEL
MODULE RELEASE
FINGER TAB
(TOP & BOTTOM)
CASE
VENT
HOLES
REAR COVER PLATE
CONNECT THIS STUD
TO A PROTECTIVE
EARTHING SYSTEM
MOUNTING STUDS AND NUTS
(14 PLACES)
8
COMM
RST KEY
7
F1 KEY
F2 KEY
6
5
DSP KEY
PAR KEY
4
3 1
2
!
MODEL EPAX
MADE IN U.S.A.
RED LION CONTROLS
YORK, PA.
RJ12
~
AC AC
~
85 - 250VAC
50/60Hz @ 5VA
CAUTION: DISCONNECT
ALL POWER BEFORE INSTALL-
ING OR REMOVING MODULE.
CONNECTED TO
MUST BE
METAL PANEL
MA2204X
E
!
Figure 4, Installing The EPAX Into A Panel
2X
(123.3)
5X 4.85
(158.2 )
(170.8)
6.72
6.23
3.36
(85.4)
0.23 (5.9) DIA.
THRU, TYP.
(604.3 )
23.79
24.27 (616.5)
+.04
-.00
+1.01
-.00
+.03
-.00
+.76
-.00
DIMENSIONS In inches (mm)
Figure 3, Panel Cut-out for the EPAX
(20 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales