Red-lion CSDIO Manual de usuario descargar pdf

 ADDS REMOTE I/O CAPABILITY TO THE MODULAR

CONTROLLER SERIES

 EIGHT INPUT, SIX OUTPUT DIGITAL MODULE

 INPUTS ISOLATED FROM OUTPUTS

 INPUTS INDEPENDENTLY SWITCH SELECTABLE FOR SINK OR

SOURCE SIGNALS

 INPUTS INDEPENDENTLY CONFIGURABLE FOR HIGH OR LOW

ACTIVE STATE

 INPUTS INDEPENDENTLY SWITCH SELECTABLE FOR HIGH OR

LOW FREQUENCY SIGNALS

 RELAY OR NFET OUTPUT MODELS AVAILABLE

GENERAL DESCRIPTION

The Model CSDIO series modules are digital I/O modules designed for use

with the Modular Controller Series. The CSDIO14 offers eight inputs and six

outputs that can be used to monitor contact or sensor inputs and actuate relays,

solenoids, PLC inputs, etc.

The inputs accept standard DC inputs or contact closures, and are configured

for Sink/Source signals via external switches. Additionally, each input has a

switch selectable input filter that can be used to prevent contact bounce. Each

input may also be software configured as a high-active or low-active input.

The modules are available with relay or NFET outputs that are capable of

switching up to one amp each (NFET DC only). For applications requiring large

loads to be controlled, several DIN rail mount relays are available.

The CSDIO modules connect and communicate via a backplane connection

to the CSMSTR Modular Controller Series Master. The CSMSTR, equipped

with serial ports as well as an Ethernet port, allows the system to share data with

PCs, PLCs, and SCADA systems. The Master supports any combination of up

to 16 CS Series modules.

Internal power management circuits allow the modules to be replaced while

power is applied, which reduces downtime in the event of a relay failure. All

configuration information is stored locally within each module, as well as in the

Master, so replacement modules do not need to be configured. The Modular

Controller Series’ high density packaging and DIN rail mounting saves time and

panel space. The backplane connection provides power and communication to

the module and snaps easily onto standard top hat (T) profile DIN rail.

CONFIGURATION

The Modular Controller Series is configured with Windows

compatible

Crimson

software. The software is an easy to use, graphical interface that

provides a means of communication configuration, as well as commissioning

and calibration of new systems.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the

manual or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Do not use the module to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the module.

MODEL CSDIO - MODULAR CONTROLLER

SERIES DIGITAL MODULE

Bulletin No. CSDIO-H

Drawing No. LP0558

Released 05/11

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

1.24

(126.5)

4.17 (105.9)

4.98

(31.5)

DIMENSIONS In inches (mm)

US LISTED

IND. CONT. EQ.

34AD

For Model No. CSDIO14S Only

FOR USE IN HAZARDOUS LOCATIONS:

Class I, Division 2, Groups A, B, C, and D

LISTED

IND.CONT. EQ.

3PWL

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF

COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I,

DIVISION 2

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I,

DIVISION 2, GROUPS A, B, C, D, OR NON-HAZARDOUS

LOCATIONS ONLY

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - SERIES DIGITAL MODULE

1 ADDS REMOTE I/O CAPABILITY TO THE MODULAR CONTROLLER SERIES EIGHT INPUT, SIX OUTPUT DIGITAL MODULE INPUTS ISOLATED FROM OUTPUTS INPUTS INDEP

Pagina 2 - CSDIO14R

2GENERAL SPECIFICATIONS1. POWER: Derived from system backplane. (CSDIO draws 170 mA max. load on power input of MASTER). Modules may be hot-swapped (r

Pagina 3 - EMC INSTALLATION GUIDELINES

3EMC INSTALLATION GUIDELINESAlthough Red Lion Controls Products are designed with a high degree of immunity to Electromagnetic Interference (EMI), pro

Pagina 4 - HARDWARE INSTALLATION

WIRINGWIRING CONNECTIONSAll conductors should meet voltage and current ratings for each terminal. Also, cabling should conform to appropriate standard

Pagina 5 - Error States

LEDSSTS – STATUS LEDThe Status LED is a dual color LED that provides information regarding the state of the module. This includes indication of the va

Pagina 6

6This page intentionally left blank

Pagina 7

7This page intentionally left blank

Pagina 8 - LIMITED WARRANTY

LIMITED WARRANTYThe Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from